QCI vs 5QI
The difference is what the number is attached to. A QCI belongs to an EPS bearer in LTE, with its values defined in TS 23.203. A 5QI belongs to a QoS flow inside a 5G PDU session, defined in TS 23.501.
For the classes you see every day, the numbers line up on purpose. QCI 1 and 5QI 1 are both conversational voice, 5 is IMS signaling in both, and 9 is the usual default for internet data in both. What 5G adds is a third resource type, delay-critical GBR, with a maximum data burst volume, plus new values for automation, V2X and XR traffic.
| Aspect | QCI (LTE / EPS) | 5QI (5G System) |
|---|---|---|
| What it labels | An EPS bearer (one bearer, one QCI) | A QoS flow inside a PDU session, identified on the wire by a QFI |
| Defined in | TS 23.203 (standardized QCI characteristics) | TS 23.501, Table 5.7.4-1 (standardized 5QI values) |
| Standardized values | 1–9 from Release 8; later 65–67, 69, 70, 75, 79, 80 and 82–85 | 1–10, 65–67, 69–76, 79, 80 and 82–90 in recent releases |
| Operator-specific values | 128–254 | 128–254 |
| Resource types | Two: GBR and Non-GBR | Three: GBR, Non-GBR and delay-critical GBR |
| Priority scale | Small numbers, some with decimals: QCI 1 = 2, QCI 69 = 0.5 | Ten times larger: 5QI 1 = 20, 5QI 69 = 5 |
| Maximum data burst volume | Not defined | Defined for delay-critical GBR only, e.g. 255 bytes for 5QI 82 |
| Usual defaults | QCI 9 default bearer, QCI 5 IMS signaling, QCI 1 VoLTE voice | 5QI 9 default QoS flow, 5QI 5 IMS signaling, 5QI 1 VoNR voice |
| Mapping to the radio | One EPS bearer maps 1:1 to one data radio bearer | Several QoS flows can share one data radio bearer; SDAP does the mapping |
The tables: same numbers, new rows
Line the two tables up and most of LTE is still there. QCI 1 to 9 came with Release 8, and 5QI 1 to 9 keep the same meaning: 1 is conversational voice with a 100 ms delay budget and a 10^-2 packet error rate, 5 is IMS signaling, and 6 to 9 are buffered TCP traffic with 300 ms budgets. The mission-critical push-to-talk values (65, 66, 67, 69, 70) and the V2X ones (75, 79) carry across as well. One wording change: LTE calls the error column the packet error loss rate.
The priority column looks different but isn't. 3GPP scaled it by ten for 5G, so QCI 1 at priority 2 becomes 5QI 1 at priority 20, which leaves room to slot new classes in between. A lower number still means more important.
5G then adds rows LTE never had: 5QI 10 for buffered traffic over satellite, with a 1,100 ms budget; 71 to 74 and 76 for live uplink streaming; and 86 to 90 for delay-critical traffic such as V2X collision avoidance, motion tracking and split rendering for XR.
Delay-critical GBR and the data burst volume
EPS has two resource types. Later LTE releases did add QCIs 82 to 85, with delay budgets as short as 5 ms, but in EPS they are still plain GBR classes.
5G makes delay-critical a resource type of its own. For a delay-critical GBR flow, a packet delivered later than the packet delay budget counts as lost and goes into the packet error rate, as long as the flow stays within its GFBR and burst volume. For ordinary GBR, the delay budget is a scheduling target, not a pass/fail line.
Each delay-critical 5QI also carries a maximum data burst volume (MDBV): the largest amount of data the RAN must be able to serve within one delay budget. 5QI 82 has a 10 ms budget and an MDBV of 255 bytes. 5QI 89, for visual content in split rendering, allows 17,000 bytes in 15 ms. That number tells the gNB how much it has to deliver inside each budget, which is what its admission decision is really about.
Bearer vs QoS flow, and interworking
The bigger change is underneath the number. In LTE, QoS lives at bearer level: each EPS bearer has one QCI, one TFT, and its own radio bearer and tunnels, and a UE can have at most 11 of them. A new treatment means a new bearer.
In 5G, QoS lives at flow level. A PDU session can carry many QoS flows over one N3 tunnel, each packet marked with a 6-bit QoS Flow Identifier (QFI) in the GTP-U header. The 5QI is part of the flow's QoS profile; the QFI is the label on the packet. They're different fields: the 5QI says how to treat the flow, the QFI says which flow a packet belongs to.
When a UE moves between 5G and LTE over N26, the combined SMF+PGW-C maps QoS flows to EPS bearers and 5QIs to QCIs. For the shared values the mapping is one-to-one. For 5QIs with no LTE counterpart, the operator has to configure what they become.
The bottom line
There's no choosing between them. QCI is what an LTE network uses, 5QI is what a 5G Core uses, and in a mixed network you'll see both for the same subscriber. Learn the shared values first (1, 2, 5 and 6 to 9), because they cover most live traffic and mean the same thing in both. Then learn what 5G added: delay-critical GBR, the MDBV, and flow-level QoS, where one PDU session carries several QoS flows and SDAP maps them to radio bearers. That last part, not the table, is what changes how you read a 5G trace.
Frequently asked questions
- Is 5QI the same as QCI?
- Not quite. Both point to a row in a standard QoS table, and the common values mean the same thing. But a QCI is attached to an EPS bearer in LTE, while a 5QI is attached to a QoS flow in 5G, and 5QI adds a delay-critical GBR resource type with a maximum data burst volume.
- What is the default 5QI for internet traffic?
- 5QI 9 is the usual choice for the default QoS flow of an internet PDU session, just as QCI 9 is the usual default bearer in LTE. Operators can pick another Non-GBR value for different subscriber tiers.
- What is 5QI 1 used for?
- Conversational voice. It is a GBR class with a 100 ms packet delay budget and a 10^-2 packet error rate, used for the VoNR voice flow. QCI 1 has the same characteristics and carries VoLTE voice.
- What does an operator-specific 5QI mean?
- Values 128 to 254 aren't standardized. An operator can define its own QoS characteristics for them, but every node that handles the flow must either be configured with what the value means or receive the characteristics explicitly in the QoS profile.
- Is the QFI the same as the 5QI?
- No. The 5QI describes how a flow is treated. The QFI is a 6-bit label in the GTP-U and SDAP headers that tells the UPF, gNB and UE which QoS flow a packet belongs to.